Frequently asked

Window film questions, answered straight.

Including the answers that cost us jobs. Every performance figure here comes from a manufacturer’s published specification for a named film — never a number we made up about your house.

Cost & value

What it costs and whether it pays

Film is priced by the square foot of glass, the film line, and how hard the glass is to reach. Anyone quoting you a price over the phone without knowing which of those applies is guessing.

How much does window film cost?

Small jobs, one problem room or a handful of windows, typically run $300 to $1,500. A whole side of the house, a main floor or every window in a smaller home typically runs $1,500 to $5,500. Whole-home coverage and large glass areas run $5,500 and up.

These are general ranges, not a quote. Each home is different and every price depends on things we can only see at your windows. The estimate is free, and we don’t price by phone. What moves the number →

Is window film actually worth it, or is it a gimmick?

It depends entirely on which problem you have. Film is very good at three things: cutting solar heat gain through glass, blocking effectively all UV, and holding broken glass together. It is a poor answer to a drafty window, an undersized air conditioner, or a room that is hot because of the roof rather than the glass.

If your complaint is that room is unusable during the day and the room has a lot of sun-exposed glass, film is usually a practical fix. If your complaint is my power bill is too high, film is one contributor among many and we will tell you so rather than promise a payback figure we cannot measure.

Will window film lower my power bill?

It reduces the solar heat coming through the glass, which reduces what your air conditioner has to remove. Whether that shows up as a number you notice on a bill depends on how much glass you have, which direction it faces, how your system is sized, and how you run your thermostat.

We do not publish a percentage saving or a payback period. We did not meter your house, and no honest installer can tell you from the curb what your bill will do. What we can do is tell you the published solar heat gain coefficient of the film on the glass you have, which is the part that is actually knowable.

How long does window film last?

Longer than most people expect. Film carries the manufacturer’s warranty, and our installation warranty matches it. We give you the warranty terms for your film in writing.

What shortens that life: cheap film, a bad install, exterior-mounted film, and ammonia-based cleaners. What you see when film fails is purple discoloration, a hazy look, bubbling, or edges lifting — all of which are warranty conversations, not normal aging.

Can I just do it myself with film from a hardware store?

You can, and for a small bathroom window it may be fine. Two things go wrong at scale. First, the film sold at retail is generally not the same product — the optical quality, adhesive and warranty are different. Second, the failure mode of a DIY install is not a slightly worse result, it is contamination and creases you cannot remove, on glass you now have to strip.

The part that is genuinely hard is not the squeegee work. It is knowing which film is safe on which glass, which is where thermal stress and voided glass warranties come in.

Heat & sun

Heat, glare, UV and fading

The short version: film changes how much solar energy gets through the glass. It does not cool a room that is hot for other reasons, and it cannot bring a room below the temperature your air conditioning can reach.
How much heat does window film actually block?

The honest answer is a range, and the right number is specific to a named film on your type of glass. Solar control films on the market span roughly from the high thirties to the high seventies in total solar energy rejected, depending on the line and shade. A clear spectrally selective film and a dark reflective film can reject similar amounts of heat while looking nothing alike.

What we do on a quote is name the exact film and show you the manufacturer’s published figures for it — total solar energy rejected, visible light transmission, glare reduction, UV rejection — against the glass you have. Film types compared explains how the types differ.

Will film make my hot room cold?

No. Film reduces the heat arriving through the glass. It does nothing about heat coming through the roof, the walls, a poorly insulated attic, or ductwork in an unconditioned space, and it cannot make a room cooler than your system is capable of.

What people consistently report is that the room becomes usable at the time of day it previously was not, the temperature swing between rooms narrows, and sitting near the window stops feeling like standing in sunlight. If someone tells you film will drop a room ten degrees, ask them which film, on which glass, measured how.

Does window film block UV?

Yes — this is the one claim film delivers on almost regardless of shade. The quality interior films we install reject 99% of UV, per manufacturer specifications, including films that look essentially clear.

That matters for skin exposure near glass and it matters for fading, though as below, UV is only part of the fading story.

Will film stop my floors and furniture fading?

It will slow fading substantially by blocking the great majority of UV, which is the biggest single cause. It will not stop fading completely, because visible light and heat also fade materials. Anyone who tells you film eliminates fading completely is overselling it.

What is the difference between heat rejection and glare reduction?

They are different problems and different numbers. Heat rejection is about total solar energy — infrared and ultraviolet included — and it is what makes a room cooler. Glare reduction is about visible light only, and it is what lets you see a screen or a view without squinting.

A spectrally selective film can cut a lot of heat while barely darkening the room, which is excellent if you want to keep a view and poor if your actual complaint is glare on a television. A darker film handles glare better. Knowing which one bothers you decides the film.

Which film is right for a window that gets a lot of sun?

Glass that gets the full sun takes it straight on, so it is usually the worst room in the house and the clearest case for solar control film. The choice is between keeping the view and killing the glare.

If the view matters, a spectrally selective film rejects most of the heat while staying relatively light. If the glare is the problem, a darker or reflective film does more. Sun-exposed glass is also where thermal stress risk is highest, so the glass type genuinely constrains the options — see the next section.

Does window film help in winter, or does it make the house colder?

A solar control film reduces solar gain year round, which in a Utah winter means slightly less free heat through exposed glass on a sunny day. In practice the summer benefit dominates by a wide margin, because the summer sun load is far larger.

If winter heat loss is your real concern, film is the wrong product category — that is an insulation and air-sealing problem. Low-emissivity films exist and do something about radiant heat loss, but they are not a substitute for a window that seals.

Your glass

Questions worth asking any installer

This is where the wrong film costs real money. Film changes how much solar energy the glass absorbs, and glass that absorbs more expands more.

Will window tint break my window?

Not when the film is matched to your glass. It’s uncommon, and the way to keep it that way is checking your glass before any film goes on. Read the full guide →

Can window film crack my glass?

Yes, and this is the single most important thing to get right. Applying film increases the amount of solar energy the glass itself absorbs rather than transmits. The glass heats, the center expands faster than the shaded edges held in the frame, and if the resulting stress exceeds what the glass can take, it cracks. This is called thermal stress fracture.

The risk goes up with: annealed glass rather than tempered or heat-strengthened, large panes, partial shading across the pane from an overhang or a tree, interior objects or heavy drapes close to the glass trapping heat, existing Low-E coatings, dark absorptive film, and edge damage or chips in the glass.

The mitigation is not luck. Film manufacturers publish glass compatibility charts specifying which films are approved for which glass construction, and we work to them. It is also why we ask about your glass before recommending anything, and why the answer is sometimes not that film on that window.

Can you put film on dual-pane windows?

Usually yes, with the right film. We check the glass, the orientation and the window’s condition first and stay inside what is safe and the window manufacturer will warranty. The full explanation →

What if my windows already have Low-E coating?

Tell us, because it changes the recommendation. A Low-E coating is already doing part of the job film would do, so the incremental benefit is smaller, and the combination of a Low-E coating plus an absorptive film can push a unit past what it can tolerate thermally.

Low-E glass is common on anything built or re-windowed in the last couple of decades in Utah, and the coating’s position within the unit matters. We check rather than assume. In some cases the right answer is a lighter film; in a few, it is no film on that window.

Will window film void my window warranty?

It can, and you should check before you buy from anyone. Some window manufacturers exclude seal failure or glass breakage from their warranty once aftermarket film is applied; others permit specific films. The terms vary by manufacturer and by product line, and we cannot speak for your window brand.

What exists to cover the gap: film manufacturers generally offer their own warranty covering glass breakage and seal failure attributable to the film, on approved glass with an approved film. That protection depends on the film having been specified correctly in the first place, which is the entire argument for getting the glass assessment right. Every film we install carries its manufacturer’s warranty, and every installation carries our window tint installation warranty, matching the manufacturer’s film warranty.

Can you film triple-pane or laminated glass?

Often, with the same caveat: compatibility is specified per film and per glass construction, and triple-pane and laminated units have their own thermal behavior. Laminated glass in particular already has an interlayer doing some of what film does.

Bring us the window and we will check the chart. The answer is a specification question with a documented answer, not a judgment call.

Can film go on the outside of the glass?

Exterior films exist and are the answer when the inside of the glass cannot be reached, or when the glass construction will not tolerate an interior film. The trade-off is lifespan: exterior film is exposed to weather and UV, so it works harder than the same product indoors. Warranty periods for exterior films are correspondingly shorter.

We treat exterior mounting as a solution to a constraint, not a default.

Looks & privacy

How it looks, and what privacy film really does

Will my windows look mirrored from outside?

Only if you choose a reflective film. Modern ceramic and spectrally selective films are built specifically to reject heat without the mirror look, and the lighter ones are hard to spot from the street.

If you are in an HOA, this is the question that matters, and it is worth checking your CC&Rs before you choose a shade — some communities restrict exterior reflectivity. We bring samples to hold against your own glass so you are deciding from the actual appearance rather than a brochure.

Does film have to be reflective to give me privacy?

It depends. Daytime privacy comes from the brightness difference between inside and out, so a film that darkens the glass helps — a neutral charcoal or a darker film offers a level of daytime privacy with a lower reflective sheen, and dual-reflective films are built to look reflective from outside while keeping a clear view from inside the home. The glass and its coating will still add some reflection in bright light. There are specific nuances that require us to see in person which dictate which films will actually provide the degree of privacy you are looking for.

If you need privacy that holds after dark, that is frosted or decorative film. You will lose the view but still get the natural light.

Can people see in at night with privacy film?

It depends on which privacy film you are thinking of. If you want privacy film that you can see through, you will get daytime-only privacy. We have several film shades that range from added daytime privacy to consistent daytime privacy. With all of these films you will still be able to see through.

If you want a film that offers both day and night privacy, you will need a frosted film. Frosted film gives day and night privacy while still letting natural light pass through. Other decorative films, such as textured, patterned or glass-design looks, can also offer day and night privacy, but they come in different levels of privacy, from least private to most private. If you are interested, we will tell you the specific privacy level of each one.

What is the difference between frosted film and privacy film?

Frosted and etched decorative films diffuse light, so nobody sees through in either direction at any time of day — the trade-off is you lose the view too. They are what you want for a bathroom, a conference room, a glass office partition or a door sidelight.

Reflective privacy film keeps the view from inside and only works one way in daylight, as above. The two solve different problems and the words get used interchangeably in advertising, which is where the disappointment comes from.

How dark are the different shades?

The number that describes it is visible light transmission — the percentage of visible light that gets through. A film described as 70% VLT lets most light through and reads as nearly clear; something in the 15–20% VLT range is visibly dark. Lower number, darker film.

There is no legal limit on residential or commercial flat glass in Utah the way there is for vehicles, so the constraint is your preference and, if applicable, your HOA.

Can you see the film once it is installed?

On a good install, from inside, essentially no. You should not see bubbles, creases, hair or debris, and the edges should be cut tight and even to the glass. A thin uniform gap at the edge is normal and intentional — it is how the film is kept out of the frame seal.

Haze or small water pockets can show for the first few weeks. That is the mounting solution curing out, and it clears on its own.

Security film

What security film does, and what it does not

The short version: security film does not stop the glass breaking. It holds the broken glass together so the opening does not become a way through. That is a delay, and delay is the entire product.
Does security film make glass unbreakable or bulletproof?

No. Nothing about a film makes glass unbreakable, and film is not a ballistic product. The glass still breaks. What changes is what happens next: instead of the pane clearing out of the frame and leaving a hole, the fragments stay bonded to the film and the assembly stays in the opening.

For a smash-and-grab that means the intruder is still outside after the first hit, and the second, and has to keep making noise. For an accident or a storm it means the glass does not become flying fragments. Those are genuinely valuable and they are not invulnerability.

How long will it hold someone out?

That depends on the film thickness, the glass, whether an attachment system was used, and how determined and equipped the person is — so a number here would be dishonest. The published standards measure defined attack scenarios rather than real-world minutes.

What we can say is that the delay is the mechanism. If your security plan is film plus an alarm plus a response, the film buys the time the rest of the plan needs. If film is the whole plan, it is being asked to do too much.

Why does security film need an attachment system?

Because without one, the film is only bonded to the glass — and the glass sits in the frame held by a glazing bead. Under a hard enough impact or a pressure load, the whole filmed pane can come out of the frame as one sheet. The glass held together and still left an opening.

An attachment system — a structural sealant bead or a mechanical profile at the perimeter — ties the filmed glass to the frame so the assembly resists as a unit. This is not an upsell: the recognized blast, windborne-debris and forced-entry ratings are achieved by the film and attachment as a system, and a film tested with attachment does not carry its rating without it.

What do the security film ratings actually mean?

They are separate standards measuring separate threats, and a film can meet one and not another:

  • ANSI Z97.1 and CPSC 16 CFR 1201 — safety glazing impact. Whether the glazing survives a defined human impact without producing dangerous fragments. This is the one that matters for a glass door or a low panel someone could walk into.
  • ASTM F1642 (with GSA TS01 hazard ratings) — blast. How the glazing behaves under a defined blast load, scored by where fragments end up inside the room.
  • ASTM E1886 / E1996 — windborne debris. Impact from a defined missile plus pressure cycling. The hurricane standards.
  • EN 356 — manual attack, graded P1A to P8B by how many blows or drops the glazing resists.
  • EN 12600 — the European pendulum impact classification.

Blast, windborne-debris and EN 356 ratings are achieved with attachment. When we quote security work we name the film, the thickness, the attachment method, and which standard the assembly was tested to — with the manufacturer’s spec sheet attached. The security film page goes through this properly.

Will security film help in an earthquake?

For the glass specifically, yes — it keeps broken glazing from becoming falling fragments, which is a real injury risk in a building with a lot of glass. In the Wasatch Front that is not a hypothetical concern.

It does nothing for the structure. Film is a glazing measure inside a seismic plan, not a seismic retrofit.

Commercial

Offices, storefronts and buildings

Can you work after hours so we do not shut down?

Yes. Most commercial work we schedule outside business hours or at weekends, because filming an occupied office during the working day is disruptive for everyone. Tell us your constraint and we schedule to it.

I lease my space — do I need the landlord’s permission?

Almost certainly, and it is worth settling before we quote. Most commercial leases treat anything applied to the building envelope as an alteration requiring written consent, and some buildings specify a uniform exterior appearance across all tenants.

In practice landlords are often receptive, because solar control film reduces load on building systems they pay to run and security film reduces their glass claims. We can provide the film specification and manufacturer documentation for you to submit.

Can you provide a CSI-format specification for our architect?

Yes. We provide a CSI-format specification section and a submittal package on request — manufacturer spec sheets, test reports, warranty documentation and samples for any film we quote.

What is anti-graffiti film and when is it worth it?

It is a clear sacrificial layer over the glass. When the glass gets tagged, scratched or acid-etched, the film is removed and replaced instead of the glass. The economics are simple: if you are replacing glass more than occasionally, film is cheaper per incident by a wide margin, and the replacement is a short visit rather than a glazing job.

It also handles hard-water etching from sprinklers and wash systems, which is a slower but equally expensive version of the same problem. More on anti-graffiti film.

Do you handle multi-site or recurring work?

Yes — property managers, retail groups and facilities teams with glass across several buildings are a good fit, including scheduled anti-graffiti replacement with a committed response window.

A deposit schedules the work, with the balance due on completion. We accept purchase orders, and terms for larger projects are set out in the written scope.

We are insured for commercial work and can provide a certificate on request.

Install & care

The install day, and living with it afterwards

Does the film go on the inside or the outside of the glass?

It depends. Most times we install the film on the inside of the window, though depending on your window type and the purpose of the film an exterior install might be the best solution.

How long does installation take?

A handful of windows is a few hours; a whole house is typically a day. What stretches it is height and access, furniture that has to move, and old film that has to come off first — removal can take longer than the install.

We work room by room so you are never shut out of the whole house, and we clear up as we go. We need clear access to the glass, so moving what sits in front of the windows before we arrive saves time.

Why is my new film hazy or full of little bubbles?

That is the mounting solution curing out, and it is normal. Film is installed wet, and the remaining moisture has to migrate out through the film. You may see haze, a slight milkiness, or small water pockets for anywhere from a few days to a few weeks — longer in cold weather, longer on thicker security films, and longer on glass that gets little sun.

What is not normal and should be reported: air bubbles rather than water, creases, debris under the film, lifting edges, or haze that is still there after 30 days.

When and how can I clean the windows?

Wait until the film has cured. Film manufacturer recommendation is 30 days — we will tell you how long for your specific install. After that, a soft cloth and a mild, ammonia-free cleaner. No scrapers, no abrasive pads, nothing with ammonia.

Can film be removed later?

Yes. Quality film from the lines we carry is designed to be removable, and it comes off without damaging the glass — it is labor, mostly in getting the adhesive residue off. Cheap film and old failed film are harder and slower, which is why removal is priced separately.

What time of year should I have film installed?

Any time. Interior film is installed inside a conditioned space, so weather is not the constraint it is for exterior work. Cold slows the cure, so winter installs take longer to clear — that is the only seasonal difference that matters.

The practical argument for not waiting until June is scheduling: everyone calls about solar film during the first real heat wave, and the calendar fills.

Working with us

About Shade N Shield

Where do you work?

Utah and Salt Lake counties in full. Davis, Wasatch and Summit counties for medium to large residential and commercial projects — reach out and we will tell you whether yours is a fit.

Every job is mobile. There is no showroom to visit, because the work happens on your glass. Every city we serve.

Are you licensed and insured?

Yes — licensed in Utah as an S230 specialty contractor through the Division of Occupational and Professional Licensing, and insured. The license number is on every contract and bid, and a certificate of insurance is available on request for commercial work.

Worth knowing as a buyer: Utah requires the license number on permits, contracts and bids, not on advertising. So the absence of a number on a competitor’s website proves nothing either way — ask them for it on the bid.

Which film brands do you carry?

As an authorized dealer: LLumar, Solar Gard, and more. A shop that carries only one manufacturer decides the recommendation before anyone looks at your glass.

Carrying several lines means we choose the film type first and then the product that suits your glass, rather than the one brand we happen to sell. Film types compared.

Is the estimate really free, and do you charge for the drive?

Free, on site, no trip charge in Salt Lake and Utah counties. We bring samples so you can hold the film against your own glass, in your own light, at the time of day that actually bothers you — which is a better basis for a decision than a swatch book.

How long does it take to get window tint scheduled?

Most estimates are scheduled within about a week, and most installs happen within a couple of weeks of approval. Film for specialty jobs has its own timeline, depending on the scope of the project. If you’re on a deadline, tell us and we’ll see what we can do.

How fast can you get to me?

Most estimates are scheduled within about a week, and most installs happen within a couple of weeks of approval. Film for specialty jobs has its own timeline, depending on the scope of the project. If you’re on a deadline, tell us and we’ll see what we can do. Summer is the busy season for solar control work; commercial and security projects are usually scheduled further out by nature.

Do you do car window tinting?

No. We install film on homes and commercial buildings only — we don’t tint vehicles.

Still stuck

Ask the question and we’ll answer it here.

We’d rather answer it once in public than fifty times on the phone. Send it over and you get a straight reply — and if it’s a question other people have, it ends up on this page.

Need an answer today? Call (801) 441-7774 or text us — that reaches us faster than anything else.

Ready for an actual answer on your glass?

Free on-site estimate. If film is the wrong fix, we say so.

Get a quote